 |
|
|
 |
 |
- Single phase input
- Built in transient protector & EMI filter
- Protection against
short circuit , overload
& overvoltage - Low ripple & noise
- Cooling by free air convection
- Power OK
indication, terminations, output
set control & rating details on front - 100% full load burn in test
- Low cost
- High reliability
- Compact
- DIN rail mountable.
- AC input voltage range .......... 90 - 130VAC & 180 - 270VAC
- AC input current(max) ........... 2A at 110VAC & 1A at 230VAC
- AC inrush current ..................16A at 110VAC & 32A at 230VAC
- Input frequency ..................... 47 ~ 63 Hz
- Efficiency ............................. 70 ~75%
- Isolation ............................... Input - Output : 2KVAC , 1minute
Input - Earth : 2KVAC , 1minute
Output - Earth : 0.5KVAC , 1minute - Overload protection ............... 105% ~ 130% of full load
- Line & load regulation ............ Better than 0.5%
- Hold up time ......................... >20ms
- Operating ambient ................. 0°C ~ 50°C, 95% RH
- Storage temperature ............. -20°C ~ 85°C
- Weight ................................. 490 grams
- Mounting .............................. 35mm DIN rail
|
Order
Code |
Output |
Ripple
& noise |
Overvoltage
|
|
|
I/P:
230VAC |
I/P:
110VAC |
|||
|
G31-70-05-05 |
G32-70-05-05 |
|
< 100mV |
<
7V |
|
|
< 100mV |
|||
|
G31-70-12-05 |
G32-70-12-05 |
|
< 120mV |
<
16V |
|
|
< 100mV |
|||
|
G31-70-12-12 |
G32-70-12-12 |
|
< 120mV |
<
16V |
|
|
< 120mV |
|||
|
G31-70-15-05 |
G32-70-15-05 |
|
< 150mV |
<
20V |
|
|
< 100mV |
|||
|
G31-70-15-15 |
G32-70-15-15 |
|
< 240mV |
<
20V |
|
|
< 150mV |
|||
|
G31-70-24-05 |
G32-70-24-05 |
|
< 240mV |
<
30V |
|
|
< 100mV |
|||
|
G31-70-24-12 |
G32-70-24-12 |
|
< 240mV |
<
30V |
|
|
< 120mV |
|||
|
G31-70-24-15 |
G32-70-24-15 |
|
< 240mV |
<
30V |
|
|
< 150mV |
|||
1. All parameters measured at 230VAC input, rated load and 25°C of ambient temperature unless otherwise specified .
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf &100uf parallel
capacitor.
3. The power supply is intended to be installed as a component inside the enclosure of a final equipment. The final equipment must be
re-confirmed that it still meets the EMC directives.
4. These units are designed for mounting on horizontal DIN rail. Ensure clearance of minimum 35mm from adjacent components for
proper ventilation.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf &100uf parallel
capacitor.
3. The power supply is intended to be installed as a component inside the enclosure of a final equipment. The final equipment must be
re-confirmed that it still meets the EMC directives.
4. These units are designed for mounting on horizontal DIN rail. Ensure clearance of minimum 35mm from adjacent components for
proper ventilation.
