SMPS for Instrument

• CE & BIS Marked
• Competitive Pricing
• Dimensions Compatible with Other Brands
• Adapter Available for Din-Rail Mount
• 100% Full Burn-in Tested

High Speed Opto Interface Modules

• 4 Channel
• Wide Input Voltage Range
• Optical Isolation between Input & Output
• High Speed Operation at 200KHz
• Compatible with PNP & NPN Type

Switched Mode Power Supply

• CE & BIS Marked
• Single Phase Input
• 35mm Din-Rail Mountable
• 100% Full Load Burn-in Tested
• High reliability

Proximity Sensor Interface

• Grouping of Terminals for PLC Connections
• Grouping of Terminals for Sensor Connections
• Common Power Supply Connections
• PNP, NPN or Bipolar Indication by Jumpers
• 35mm DIN Rail Mountable

Black Series SMPS

• BIS Marked
• 35mm Din-Rail and Screw Mountable
• 45 Degree Inclined Screw Type Terminations
• 100% Full Load Burn-in Tested
• High reliability, Low Cost

Power Distribution Modules

• Voltage Rating: 100VDC / 230VAC
• Current Rating Input: 10A max
• Current Rating Output: 5A per channel
• Input side: 1 x 2 way Terminals
• Output side: 6 x 2 way Terminals

DC-UPS

• Single Phase Input
• Built-in Transient protector & EMI filter
• Battery low protection
• Battery reverse polarity protection by fuse
• Cooling by free air convection (Internal Fan for 12V model with automatic fan control)

Precision Reference Voltage Source 10VDC: 20mA

• Single Phase Nominal Input
• Designed to deliver accurate reference inputs for a wide range of equipment, such as VFDs and LVDTs
• 100% Full Load Burn-in Tested
• High reliability, Low Cost.
• Compact

Battery Chargers

• BIS Marked
• Automatic Float Boost Changeover and Fan Control
• Operates as FCBC or SMPS at Float voltage
• Short Circuit & Overload Protection Auto Recovery Type
• Battery Reverse Polarity through relay

Voltage Monitor Relay

• Monitors DC input voltage
• The Unit Triggers internal timer when input voltage goes above set voltage
• After Set time delay (0-60 sec), Relay change over occurs
• UV & OV Relays Energize (Gets ON) When Power Supply Voltage is Within Respective Set Range
• Resets if input voltage comes down below set voltage.

Standard Interface Modules

• 1 N/O, 1C/O, 2C/O Contacts
• LED & Freewheeling Diodes across Coil
• Reverse Polarity Blocking Diode
• 24VDC / 230VAC Coils
• +VE / -VE or Isolated Looping by Jumpers (Site Selectable)

D-SUB to Screw Terminator

• Available in Both Male and Female Type Connector
• Available No. of Pins. 9, 15, 25, 37, 50
• Voltage Rating: 100VDC
• Current Rating: 500mA
• 35mm Din-Rail Mountable

Space Saver Relay Modules

• 8 Channels
• 1C/O Contacts
• 3 Space Saver Modules Occupies 150mm Only
• LED & Freewheeling Diodes across Coil
• Reverse Polarity Blocking Diode.

FRC to Screw Terminator

• Available in Both Male and Female Type Connector
• Available No. of Pins 10, 14, 16, 20, 26, 34, 40, 50, 60, 64
• Voltage Rating: 100VDC
• Current Rating: 500mA
• 35mm Din-Rail Mountable

Solid State Interface Module

• Isolated & Non-Isolated SSR with Solenoid Driver
• Wide input voltage range
• Low Input Current
• Fuse at output for over current protection
• Can be used as NPN to PNP Converter or vice versa

Generator Control Interface Module

• 1 N/O 70A contacts
• 1 C/O 5A rated contacts
• Reverse blocking diode
• Two Contacts rated for 70A @12V / 35A @ 24V
• LED & Freewheeling diode across coil.

Hooters

• Available in 2 Tone, 8 Tone
• LED Flasher
• Volume Control
• Audio Level: 110dB
• Universal Supply
• Wall Mount / Base Mount

CNC Specific Relay Module

• 50 pin Male FRC Connector
• 24 inputs, 24VDC each
• 16 channel, 1 C/O Relays
• OEN Relay
• LED & Freewheeling diode across coil

Analog Signal Converters

• 22.5mm Single Output Slim Converter
• Available in Both Single Input – Single / Dual Output
• Aux. Supply: 18 to 32VDC & 90 to 270VAC
• 3 Point and 4 Point Isolation
• DIN Rail Mount

Vibrator Control Interface Module

• Input: 230VAc, 43-63Hz
• Output: Half wave phase controlled DC, 2A max
• Presets to set Coarse and fine control
• Facility to connect external potentiometer or external 0 to 10VDC
• DIN rail Mountable

Cables

• Available with FRC and DSUB Connector
• Current Rating: 500mA
• Variable Lengths: 1M, 2.5M, 5M, 10M
• FRC Cable is Configured with Reverse Polarity, as Required
• D-SUB to D-SUB Cables are Supplied in Both Shielded and Non-Shielded Variants

Modbus

• Cost effective expansion of existing PLC system
• Cost effective control of remote field devices
• Control of field devices from personal computer
• Data acquisition
• Cost effective control of remote field devices